Advanced Diploma In Electrical Design Engineering
 

Electrical Design Academy: Engineering Training with Practical Examples and Hand-on Training for EPC Sector & MEP Sector
What you'll learn
⚡ Complete Electrical Design Engineering Training with Practical Example and Hands-on Practice
⚡ Electrical equipment design for all projects like: oil & gas, chemical, power, pharmaceutical etc.
⚡ Detail engineering: Single line diagram, cable routing layout, earthing layout, lightening layout, lighting layout, substation layout, equipment layout
⚡ Electrical Heat Tracing Design, Calculation and Layout
⚡ Cathodic Protection, Cathodic Protection for Underground Plant Piping
⚡ System Study: Load flow analysis, short circuit analysis, relay coordination, motor starting study, harmonic study
⚡ 3D Modeling, 2D Droughting, Analysis on software like: ETAP, DIALux, AutoCAD
⚡ Hazardous area classification
⚡ Lightning risk calculation, Report generation and layout
⚡ Coordination with other departments for input / output
Requirements
❗ ETAP Software: for System Study / Simulation
❗ DIALux software: for LUX calculation and layout
❗ AutoCAD Software: for making the layout
❗ Scientific Calculator: for sizing and calculation of electrical equipment
❗ MS Excel: for making the datasheet / equipment specification for procurement purpose
Description
The goal is to design safe and dependable processing facilities in a cost effective manner. The fact is that there are very few formal training programs that focus on design and engineering of Electrical systems of such big plants The heavy electrical industry has under its purview power generation, transmission, distribution and utilization equipment. These include turbo generators, boilers, turbines, transformers, switchgears and other allied items. These electrical equipment (transformers, switchgears, etc.) are used by almost all the sectors. Some of the major areas where these are used include power generation projects, petrochemical, refineries, chemical plants, integrated steel plants, non-ferrous metal units, etc.
Overview:-
✨ Introduction of Electrical Engineering
✨ Introduction of EPC Industry
✨ Coordination with Other Department
Load List:-
✨ Preparation of Load Schedule
✨ Determination of Power Supply Capacity
✨ Standby Capacity consideration
✨ Rating of Generators in Relation to
✨ Prime Movers Importance of max and min temp
✨ Rating of Motors in Relation to their Driven Machines
Electrical Equipment Selection, Sizing:-
✨ Motor
✨ Transformer
✨ Emergency Generator
✨ Neutral Grounding Resistor (NGR)
✨ Power capacitor banks (PCB)
✨ AC UPS
✨ Battery & Battery Charger
✨ CT/PT
✨ Bus duct
Illumination Design:-
✨ Introduction
✨ Type of Lighting Fixtures
✨ Selection of Lighting Fixtures
✨ Preparation of Fixtures Schedule
✨ Indoor Illumination Calculation
✨ Outdoor Illumination Calculation
✨ Calculation on Software
✨ Lighting Layout Design
✨ Lighting Installation Detail
✨ Small Power selection
✨ Lighting Board Schedule
Cable Selection, Sizing & Layout:-
✨ Power and Control cable Introduction
✨ Cable Selection and Sizing
✨ Cable sizing for Low voltage system
✨ Cable sizing for High voltage system
✨ Voltage Drop Consideration
✨ Let through Energy consideration
✨ Earth fault Loop Impedance consideration
✨ Cable Schedule
✨ Cable interconnection Schedule
✨ Selection and Sizing of cable Tray
✨ Cable tray schedule
✨ Cable Drum schedule
✨ Conduit Selection
✨ Conduit Sizing
✨ Cable Routing Layout
✨ Cable Tagging
✨ Installation details
Development of Single Line Diagram (SLD):-
✨ Key SLD
✨ Detail SLD
✨ Lighting system SLD
✨ Small power SLD
✨ Metering and Control diagram
Earthing & Lightening Protection Design:-
✨ Requirement of Earthing in Industrial Plants
✨ Earthing Design calculations
✨ Type of Earthing and Details
✨ Earthing Installation Details
✨ Earthing Layout Design
✨ Lightening Protection Requirement
✨ Lightening Protection Calculation
✨ Lightening Installation Details
✨ Lightening Layout Design
✨Testing / System Studies:-
✨ Overview & Load Flow Analysis
✨ Short Circuit Analysis (Fault Level Calculations)
✨ Motor Starting Study
✨ Relay- Coordination
Who this course is for
⭐ ITI / Diploma / Degree / Master in Electrical or Electronics
⭐ Fresher / Experienced
⭐ People from other engineering background can also do the course if they have good math and electrical base experience.
Homepage